SmartGen

Owned by arkadi kaplon
Last updated: 18.04.24
4 min read

 

image-20240326-073459.png
image-20240326-073551.png

 

Supported Models

HGM6120N (Generator Controller)
SGUE485 (USB to RS485 Converter)

Communication Method

RS485 (Via Convertor)

Network configuration

Device Baudrate

9600

Device Baudrate

9600

Supported Services

Parameters

Alarm Name

Alarm Criticality

Remote Controlling

Parameters

Alarm Name

Alarm Criticality

Remote Controlling

Engine Hours

 

 

 

Voltage_Phase_1-2

 

 

 

Grid_Voltage_Phase_1_3

 

 

 

Current_Phase_1-3

 

 

 

Frequency

 

 

 

Engine_Speed

 

 

 

Battery_Voltage

 

 

 

Coolant_Temperature

 

 

 

Oil Pressure

 

 

 

Total Output KWH

 

 

 

Working_Mode

 

 

 

Installation and Configuration

Preparation

  • Galooli Gateway (Including an active SIM card).

  • Power source for the Gateway.

  • Power cables for the Gateway. Two cables with a thickness of 0.5mm. The length of the cables is determined by the distance between the power supply and the Gateway.

  • SmartGen Geset HGM6120N Controller + SGUE485 (USB to RS485 Converter).

  • USB A-B cable

  • 2 x 120 ohm resisters.

  • Screwdriver (Slotted & Phillips).

  • Download the SmartGen Configuration Software

Installation

In the installation process mentioned bellow, the images and steps describe the Galooli Elara gateway installation, however any other Gateway can be connected.

  1. Assemble the Galooli gateway and ensure there is a power source available and that it is connected correctly to the Gateway. Gateway Solutions

  2. Connect the USB cable from the SmartGen controller to the SGUE485 (USB to RS485 Converter).

  3. Connect 2 RS485 communication cable between the SGUE485 (USB to RS485 Converter) and the Galooli Gateway RS485 input.

  4. One resistor should be installed on the SGUE485 (USB to RS485 Converter) and one resistor should be installed on the Galooli Gateway.

  5. If necessary, mount all the devices on a din rail.

  6. The Galooli gateway should be powered on.

  7. Ensure that all devices are turned on.

Module Address Configuration

  1. Open the iGMP6V configuration software

  2. Connect the USB A-B cable between the SmartGen and the computer.

  1. As soon as you return to the IGMP6 software, you should see a message notifying you that the communication has been established and a suggestion that you read the SmartGen configurations. Click on "OK".

 

 

  1. Click on “Module” > “Module Settings” > Change the “Module Address” if necessary. In the event that additional settings need to be configured, please do so at that time.

  1. If all the relevant configurations have been completed, please click on the "Connection" tab >> "Write Config" >> wait until a completion message appears.

Power Center Configuration

  1. Open the Power Center (if the power center was already open, close it, and re-open it).

  2. Log in

  3. Open the “Active Device” drop-down menu and select “Elara”.

  1. Open the “Connect Via” drop-down menu and select the “OTA” or “Serial” connection.

  1. Your credentials and the ID of the unit should be entered.

  2. Navigate to the “Elara” tab.

  1. Navigate to the “Configuration” tab.

  1. In the “Configure” tab click the “Add Port 1 Device”.

  2. The “Elara – Modbus Device Configuration” window will pop up, select the “Generator” device and the relevant module of the “SmartGen” controller. Ensure that the physical device ID is - 10 and the baudrate is 9600. Apply the changes.

  1. Click the “Write Configuration” button to save the changes.

 

11. Click the “Reset” button.

11. Navigate to the “Status” tab to view the status of the generator controller.

Galooli Solution Configuration

  1. Open the Galooli Solution

  2. Select the “Manager” Solution >> “My Units” menu

  3. Click on the relevant unit in the organization tree

  4. Select the “Configuration” tab >> “Device Configuration” sub-tab

  5. Select the “Section: Generators” >> check the “DG X” relevant panel