Supported Models	Communication Methods	Read/Write Community
Eltek_SmartPack	RS485	Not Relevant
Eltek_SmartPack2	RS485/SNMP	Read - public Write - v1private
Eltek_SmartPack2Touch	SNMP	Read - v1community Write - v1private
Eltek_SmartPackS	SNMP	Read - v1community Write - v1private

Network Configuration for ETHERNET/SNMP Connection

Device IP	192.168.10.20
Subnet mask	255.255.255.0
Gateway	192.168.10.1
Host IP (Web/Elara configuration)	192.168.10.21

Network Configuration for RS485 Connection

Device Baudrate	19200

RS485 Wiring Diagram

SmartPack Configuration

Username - admin
Password - admin

SmartPack2 Configuration

Smart_Pack2 Touch + SmartPack S Installation & Configuration

Now that you have installed the appropriate gateway on site, it is time to connect it to the rectifier via the ethernet interface that is supported by the SmartPack 2 touch and SmartPack S.
Connect the Galooli gateway to the rectifier using an Ethernet cable. The technical booklet will specify the specific name, model, and port of the gateway.
In order to configure the Power Center and Galooli solution, please refer to the relevant links for your gateway.

Gateway	Link
Elara	https://galooli.atlassian.net/wiki/spaces/KP/pages/2643558401/Elara+Installation+and+Configuration#APN-%26-Cloud-Server-Configuration
TechBase	https://galooli.atlassian.net/wiki/spaces/KP/pages/2882338951/Techbase+NPE+X500+M3+Installation+and+Configuration#Computer-Connections

SmartPack2 & S Touch SNMP Configuration

The following steps should be taken as soon as you receive your new “SmartPack 2 and S Touch Rectifier”:

1. In order to activate the SNMP option after installation, login to the rectifier controller and copy your
specific MAC address.

2. You will need to contact a representative from "Eltek" to activate the SNMP feature; you will need to
provide the MAC address from the previous paragraph and ask for a "license key.”

3. Once the "license key" has been reserved from "Eltek", enter it and proceed to the next step.

4. Check the “Web-based configuration” to enable the web SNMP configuration.

SNMP is now available

Supported Parameters (SNMP)

Power Center Parameters SmartPack S	Power Center Parameters SmartPack2 Touch	System Parameters	Remarks
	Total_Output_KWH	Rectifier_X.Total Load Energy [KWH]
Voltage		Rectifier_X.U_System [V]
Current		Rectifier_X.I_Load
Battery_Current		Rectifier_X.I_Battery
Battery_SOC_Percentage		Rectifier_X.State_Of_Charge
Battery_Temperature		Rectifier_X.Temperature_Battery [Celsius]
Internal_Temperature		Rectifier_X.Temperature_Internal [Celsius]
Solar_Curent		Rectifier_X.Solar_Current [A]
Solar_KWH		Rectifier_X.Solar_Total_Power [KWH]
Solar_1-8_Voltage	Solar_1-4_Voltage	Rectifier_X.Solar_Voltage_X [V]	Solar modules data
Solar_1-8_Current	Solar_1-4_Current	Rectifier_X.Solar_Current_X [A]	Solar modules data
DG_Signal		Rectifier_X.Generator Signal
Rectifier_Current		Rectifier_X.I_Rectifier [A]
Installed_Modules		TBA
Installed_Solar_Modules		TBA
Faulty_Modules		TBA
Faulty_Solar_Modules		TBA

Supported Parameters (RS485)

Power Center Parameters SmartPack	System Parameters	Remarks
Serial-1
Total_Output_KWH	Rectifier_X.Total Load Energy [KWH]
Solar_KWH	Rectifier_X.Solar_Total_Power [KWH]
Rectifier_Current	Rectifier_X.I_Rectifier
Battery_Temperature	Rectifier_X.Temperature_Battery [Celsius]
Current	Rectifier_X.I_Load
Voltage	Rectifier_X.U_System [V]
Battery_SOC_Percentage	Rectifier_X.State_Of_Charge
Digital_Inputs	TBA
Digital_Outputs	TBA
Solar_Curent	Rectifier_X.Solar_Current [A]