Vehicle Gateway - K2T

Vehicle Gateway - K2T

image-20250504-052115.png

The K2-T is a professional vehicle tracking device, designed for real-time fleet monitoring using LTE Cat 1, 2G, and GNSS connectivity. It supports RS232/RS485 interfaces for integration with various vehicle sensors and features dual SIM functionality for cost-effective international vehicle tracking.

Disclaimer on Fuel Monitoring Data Quality

When fuel data is sourced from external (non-Galooli) hardware, the accuracy and reliability of the data primarily depend on the third-party device itself. While Galooli applies advanced processing and correction methods to enhance the quality of incoming data, full accuracy cannot always be guaranteed.

Item Name

Galooli PN.

Item Name

Galooli PN.

Vehicle Gateway - K2T

400-K2TelF125-020

Features

  • Real-time vehicle tracking

  • Dual SIM for reduced roaming costs

  • RS485 for third-party sensor integration

  • Internal high-gain GNSS and LTE antennas

  • GPS Time (Galooli internal cloud side logic only)

  • Driver Behavior:

    • Movement sensor

    • Ignition switch

    • Geofencing

    • Idling

  • Dallas Button Key

  • Immobilizer (Automotive Relay)

  • Fuel Measurement:

Certification and Approvals

CAN Bus Integration (K2T LV-CAN200)

The K2T gateway supports CAN Bus data collection using K2T CAN adapters (e.g., LV-CAN200). This integration enables direct access to vehicle ECU data such as fuel level, RPM, speed, and mileage. For full installation and configuration instructions, refer to: https://galooli.atlassian.net/wiki/x/E4CDKQE

Hardware Specifications

  • LTE CaT 1 / 2G (GSM/GPRS) / GNSS

  • Dimensions: 65 x 56.6 x 20.6 mm

  • Weight: 55 g

  • Operating voltage: 10–30 V DC

  • Internal battery: 170 mAh Li-Ion 3.7 V

  • Operating temperature: -20°C to +40°C (with battery)

  • Operating temperature: -20°C to +85°C (without battery) 

  • IP Rating: IP41

  • Memory: 128MB internal flash

  • Interfaces: RS232, RS485, 1-Wire, USB 2.0, Analog/Digital I/Os

  • GPS Time - The GPS location time is updated according to Galooli cloud-side logic:

    1. When the unit reports a valid location, including valid satellite data, the GPS time is set according to the unit time.

    2. When the location is not valid, the GPS time is not updated. Instead, it remains locked to the last time it received a valid GPS location.

  • Dual SIM (2 SIM card slots) 

image-20250612-084951.png

Fuel Level Sensors – Supported Signal Types

Please be advised that the unit supports the Omnicomm LLS sensor as well as standard vehicle fuel level senders (floats), provided they utilize a voltage output. This capability is consistent with other integrated K2T devices.

Important Requirements:

  • Supported: 0–30V DC analog voltage signals

  • Not Supported: Pulse-based, frequency-based, or other non-voltage signal types.

  • Digital LLS: 1 sensor on RS-232, up to 5 sensors on RS-485 (up to 16 with firmware 03.28.xx and later).

Pinout

Pin #

Color

Name

Description

 

 

 

 

 

image-20250612-084132.png

 

1

Red

+10- +30 V DC

Power

2

Grey

AIN 1 / DIN 2

Analog input, channel 1. Input range: 0-30 V DC
&

Digital input, channel 2

3

White

RS232-RX

RS232 Receive (RX)

4

White Green

RS232-TX

RS232 Transmit (TX)

5

Yellow

DIN1

Digital input, channel 1

6

White Blue

INPUT 6

TX EXT (LVCAN – TX)

7

Black

GND

Ground

8

Orange

DOUT1

Digital output, channel 1. Open collector output. Max. 0.5 A DC

9

Purple

RS485-A

RS485 Line A

10

Blue

RS485-B

RS485 Line B

11

Green

1WIRE DATA

1-Wire Data Line

12

White Yellow

INPUT 5

Digital Input 5

Wiring Scheme

image-20250612-114432.png

LED Indication

image-20250612-085055.png

Navigation LED Indications

Behavior

Meaning

Behavior

Meaning

Permanently switched on

GNSS signal is not received

Blinking every second

Normal mode, GNSS is working

Off

GNSS is turned off because: device is not working or device is in sleep mode

Blinking fast constantly

Device firmware is being flashed

Status LED Indications

Behavior

Meaning

Behavior

Meaning

Blinking every second

Normal mode

Blinking every two seconds

Sleep mode

Blinking fast for a short time

Modem activity

Off

Device is not working or device is in boot mode

Physical Installation & Configuration

Standard SIM Card & Battery Assembling

image-20250612-090830.png

Configuration

  1. Connect a micro USB cable between the K2-T device and the computer.

image-20250612-090014.png
  1. Connect the K2-T to a power source (10–30V).

  2. Download and open the “Teltonika Configurator” software.

  3. In the “Teltonika Configurator” click on the image shown below.

image-20250612-092304.png
  1. Click “Load from file” and upload the following file:

  2. Click on “Status” and copy the “Device IMEI”.

image-20250612-112223.png
  1. Click on “GPRS” and configure the “Server Settings”:

    1. “Domain” (Server URL) - As per your standard setup.

    2. “Port” - should be always “5028”

If you're unsure about the parameters, please contact the Galooli Accounts team by opening a support ticket - Galooli Support Tools.

  1. Check the “SIM1 GPRS Settings” & “SIM2 GPRS Settings” and ensure that the SIM card's APN is correctly configured.

image-20250612-113517.png
  1. After making all the changes, click “Save to Device” to apply the settings.

image-20250612-111048.png
  1. You may now close the “Teltonika Configurator”.

  2. Open the Galooli Solution → Manager Application → My Units → Add a new unit.

  3. The ID must be the Device IMEI you copied earlier. Fill in all other mandatory information related to the unit and save the changes. https://galooli.atlassian.net/wiki/x/AYC0q

image-20250612-091018.png
  1. Next, open the Panorama application, locate the vehicle in the organization tree, and ensure the K2-T is connected to the server.

  2. Disconnect the K2-T from the power source.

  3. Finally, disconnect the micro USB cable and close the gateway cover.

image-20250612-085806.png

Physical Connection to Vehicle

Connecting Wires

  • Wires should be fastened to the other wires or non-moving parts. Try to avoid heat emitting and moving objects near the wires.

  • If the wires are placed in the exterior or in places where they can be damaged or exposed to heat, humidity, dirt, etc., additional isolation should be applied.

  • Wires cannot be connected to the board computers or control units.

Connecting Power Source

  • It is recommended to connect to the main power cable in the fuse box.

  • Use 3A, 125V external fuse.

  • When module is connected, measure voltage again to make sure it did not decrease.

Connecting Ignition Wire

  • Be sure to check if it is a real ignition wire i.e. power does not disappear after starting the engine.

  • Check if this is not an ACC wire (when key is in the first position, most of the vehicle electronics are available).

  • Check if power is still available when you turn off any of vehicles devices.

  • Ignition is connected to the ignition relay output. As alternative, any other relay, which has power output when ignition is on, may be chosen.

Connecting Ground Wire

  • Ground wire is connected to the vehicle frame or metal parts that are fixed to the frame.

  • If the wire is fixed with the bolt, the loop must be connected to the end of the wire.

  • For better contact scrub paint from the spot where loop is going to be connected.

Manufacturer Data