...
Hardware Specifications
General Specifications
Feature | Parameters | |
|---|---|---|
Power Supply | 9 - 30 V | |
Power Consumption | Full power mode | 0.5 W average (Approx.) |
Low power mode | 0.2 W average (Approx.) | |
Deep Low power (backup battery only). This mode is not available in K2-CAN type devices | 250uA (Approx.) | |
Internal Backup Battery | Li-ion 950mA | |
GSM/GPRS | Antenna Type | Internal |
Active Channels | 48 | |
Sensitivity | -163 DB | |
Driver Identification | Dallas button / Keypad/ RFID cards | |
General Purpose Inputs | Up to 5 general-purpose inputs, can be configured to Analog or digital mode separately. | |
Outputs | Dedicated immobilizer output | |
Serial Communication | RS485 | |
Memory Logger | 7500 messages (Approx.) | |
Storage Temperature | -40 -85 Celsius | |
Working Temperature | -20 -70 Celsius | |
Max. Relative Humidity | 90% | |
Weight | 120 g (Approx.) | |
Cellular Network | 2G | |
SIM Card Requirements | Use only GSM and not CDMA support Quad-band GSM | GPRS: 850/900/1800/1900 MHz which is not CDMA frequencies Open for 2G only 10MB package
| |
SIM Card Data Usage | The SIM card data usage may change depending on its use. As an example, a car that operates 24 hours a day will consume a greater amount of data. | |
Output Specifications (Immobilizer)
Parameter | |
|---|---|
Output Type | Open Collector |
Max. Continuous Working Current | 200 mA |
Over Current Protection | 300 mA (Approx.) |
Maximum Working Voltage | 30 V |
General Purpose Inputs Specifications
Parameter | |
|---|---|
Reading Voltage Range | 0-30 V |
Reading Resolution | 10 mV |
Reading Accuracy (max error) | 2% |
Each input can be configured separately to have digital state threshold levels (Using the configuration center).
...
Negative Digital Inputs Specifications
Parameter | |
|---|---|
Low-Level Threshold (Active) | 2 V |
High-Level Threshold | 3 V |
Temperature Sensor Input Specifications (NTC)
Parameter | |
|---|---|
Temperature Range | -20 -70 Celcius |
Accuracy | 1 degree Celcius |
Resolution | 0.25 degree Celsius |
Odometer Specifications
Parameter |
|
|---|---|
| ±5% It is recommended that the odometer and Galooli system be synchronized at least once a year or when the gateway is replaced/fixed. |
Indication LEDs
...
Status LED Indications
Status | |
|---|---|
Power-up/ Reset | 1 sec Red light, followed by 1 sec Greenlight |
Normal Operation | Valid GPS location - Green light slow blink. No GPS location - Red light slow blink |
Driver Identification | Fast blink |
Network Jamming detected | Fast blink - Alternating Green/Red light |
Network LED Indication
Status | |
|---|---|
Connected to host server | Greenlight blink |
GSM Network found | Red light, low blink |
Searching network | Red light, short blink |
SMS Commands
Request Commands
...
The TritonK2 use a standard 12-pin harness as described below:
...
Pin # | Color | Name | Description |
|---|---|---|---|
1 | Yellow-white | RS485 A | Serial communication with external devices & configuration center |
2 | Green-brown | RS485 B | Serial communication with external devices & configuration center |
3 | Green | Input 5/ CAN-H | General purpose, negative digital input (active when connected to ground). K2 - CAN type - used as CAN-H input |
4 | Blue | Buzzer | Dedicated buzzer output, used for in-vehicle alerts |
5 | White | Dallas/Keypad | External driver identification device connection |
6 | Red | Power in | Power in (9-30v) |
7 | Orange | Input 1 / Ignition | General-purpose Analog / Digital input. Dedicated connection for Ignition signal |
8 | Brown | Input 2 / Panic | General-purpose analog/ Digital input. Dedicated connection for Panic button |
9 | Pink | Input 3 | General-purpose Analog/ Digital input |
10 | Grey | Input 4 / CAN-L | General-purpose Analog/ Digital input |
11 | Purple | Out/ Immobilizer | Immobilizer output control |
12 | Black | GND | Ground connection |
Notes:
All pins marked as Analog/Digital inputs can operate both as Analog and Digital inputs. Voltage thresholds for digital behavior are defined using the 'Configuration Center' application.
Negative Digital inputs have an internal pull-up, so 'activating' those inputs is done by connecting to ground.
Installation Video
| Child pages (Children Display) |
|---|